All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
When you pull up to your garage door and push the button for the opener, there’s one thing that should happen: your garage door should open smoothly, steadily, and quietly. However, if that’s not happening, contact the friendly professionals at Garage Door Service. We’re located in Loveland, Colorado, but we’re also prepared to offer service, garage door repair, and garage door opener repair to customers in Fort Collins, Windsor, and all over Northern Colorado, as well as Wyoming, Nebraska, and Kansas. No matter the problem, our technicians always come prepared with a wide range of parts and tools, so that we can repair your garage door during a single visit. We’re committed to providing reasonable rates, free estimates, and top-notch customer service. Our goal is to leave you with a working garage door and a smile.
I chose Precision because of an ad I saw advertising free service call. I was looking to replace the sensors on 2 garage doors. Ben the tech- very nice and knowledgeable told me I would have to replace both units because the base unit was too old. Fine not what I was looking to do but I understood until he quoted me over $900 for 2 units. My friend just had hers replaced for $350. When I told Ben I would think about it He said that would be $80 for the service call. My free coupon only works if you get a repair. It took less than 15 mins. Needless to say I have called a few other companies and the going rate is $340-$350 no service fee
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
If the outlet has power, but there’s no sound or no lights when you push the wall switch and remotes, you probably have a bad circuit board. Lightning strikes are the most frequent reason for the demise of a circuit board. The circuit board consists of the entire plastic housing that holds the lightbulb and wire terminals. The part number should be on the board itself.
Typically, it will cost less to install a steel garage door without an opener than to install a custom wood door with a garage door opener. Recent innovations have also yielded high-tech doors with thick insulation and energy-efficient glaze, as well as finished interior surfaces and other significant upgrades. These are more expensive doors, but they are also extremely durable.
When you pull up to your garage door and push the button for the opener, there’s one thing that should happen: your garage door should open smoothly, steadily, and quietly. However, if that’s not happening, contact the friendly professionals at Garage Door Service. We’re located in Loveland, Colorado, but we’re also prepared to offer service, garage door repair, and garage door opener repair to customers in Fort Collins, Windsor, and all over Northern Colorado, as well as Wyoming, Nebraska, and Kansas. No matter the problem, our technicians always come prepared with a wide range of parts and tools, so that we can repair your garage door during a single visit. We’re committed to providing reasonable rates, free estimates, and top-notch customer service. Our goal is to leave you with a working garage door and a smile.
A1 Garage Door Service Dallas never settle for less because we always want our customers to have the best. Because of this, we only hire technicians who are already back by years of experience in the field. We make sure that they have sufficient training before being deployed to the homes of our loyal customers. They even go through a series of criminal background checks before they are employed so that we can make sure that our customers’ safety will never be compromised. Also, they continuously strive to learn more about newly released garage doors and products in the industry so that they are always updated and continue to be masters of the craft. With A1 Garage Door Service Dallas always the first to utilize the most advanced technology and tools in the market, this makes us undefeated when it comes to providing world-class garage door services.
Sears Craftsman Garage Door Openers are America’s favorite. We have several options to choose from that will fit your individual needs. Sears garage door opener selections includes 1/2 horsepower, 3/4 horsepower, belt and chain drive as well as the Craftsman Smart Control garage door opener which allows you to control and monitor your garage door even when you are away from home.
Once the chain is secure, separate it from both sides of the trolley. Disconnect the rail from the header bracket and move the rail off to one side. Slide off the old trolley, and slide on the new one. Reattach the chain and adjust the chain tension. Replacing the trolley on a belt drive and replacing it on a screw drive are similar procedures. A new trolley will cost $25 to $40 depending on your model.

R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.

Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers.  It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.


Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.
No matter what type of garage door opener you have, you should always lube the rail where it comes in contact with the trolley carriage. Use a lubricant that doesn’t attract dirt. Silicone spray is a good choice. If you have a screw-drive opener, you’ll need to grease several spots along the rail gear at least once or twice a year. In colder climates, use lithium grease, which won’t harden when the temperature drops. Many home centers sell specifically formulated products near the openers. And don’t use too much or it could drip on your car.
Given the complexity of a garage door and opener system, there are a variety of different areas something could go wrong. If your garage door shakes or is very loud during operation, the garage door closes all the way only to immediately open back up, the garage door opens slowly or closes too quickly, or the garage door opener and remote aren't working at all, you should seek help from a professional garage door repair specialist.
Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.
Nick knew what the problem was right away. He told me the options and explained them. He answered my questions and even some from a family member. He was efficient, knowledgeable, and courteous. This was my first experience with your company, but if I need further assistance I will certainly call you again. Hopefully, Nick will be available. My brother was impressed with him, too.
I have 2 full house humidifiers that have stopped functioning right. There are new filters, fan runs, tanks are full of water but they are not empting into the base. They have worked for part of the winter and now nothing seems to help...I loosened the caps thinking I had them too tight..... nothing seems to work .I have had humidifiers for 20 years and this is the first time this has happened to me. The humidifiers are only 2 years old. Any suggestions??

Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.

Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.
10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.
If the outlet has power, but there’s no sound or no lights when you push the wall switch and remotes, you probably have a bad circuit board. Lightning strikes are the most frequent reason for the demise of a circuit board. The circuit board consists of the entire plastic housing that holds the lightbulb and wire terminals. The part number should be on the board itself.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
A garage door is a good investment because it allows your properties to look better than ever. It significantly adds market value to your homes and enables it to have a better curb appeal. This is why you have to choose the best one to equip with your garage doors. We have them in different brands here and they can also be custom made. Plus, they come at the lowest possible prices. Call us now at 469-294-2007 to know more about the products we provide.
With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
×